Dukane DPC II Plus Manuel d'utilisateur Page 21
- Page / 190
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
11
Dukane Manual Part No. 403–566–01
Section 2 – Safety Tips
Health and Safety Tips
Please observe these health and safety recommen-
dations for safe, efficient, and injury-free opera-
tion of your equipment. In this manual, the term
system refers to a complete group of components
associated with the welding of plastic or metal
parts, also known as an ultrasonic assembly sys-
tem. A typical system consists of a generator and/
or ultrasonic process controller, start and stop
switches, power controls, connecting cables, and
the probe assembly which includes the transducer,
booster, horn and replaceable horn tip.
Proper Installation – Operate system components
only after they are properly installed and checked.
No Unauthorized Modifications – Do not modify
your system in any way unless authorized to do so
by Dukane Corporation. Unauthorized modifica-
tions may cause injury to the operator and/or equip-
ment damage. In addition, unauthorized modifi-
cations will void the equipment warranty.
Keep the Cover On – Do not remove the equip-
ment cover unless specifically directed to do so by
Dukane Corporation. The generator produces haz-
ardous electrical voltages which could cause in-
jury.
Grounded Electrical Power – Operate this equip-
ment only with a properly grounded electrical con-
nection. (See Electrical Safety Grounding Instruc-
tions on the next page.)
Comply with Regulations – You may be required
to add accessories to bring the system into com-
pliance with applicable OSHA regulations.
CAUTION
Parts being joined ultra-
sonically sometimes
vibrate at audible fre-
quencies. Wear ear
protection to reduce an-
noying or uncomfortable
sounds. In addition,
sound absorbing materi-
als, enclosures or sound
deflectors may be in-
stalled to reduce the
noise level.
IMPORTANT
Never operate the DPC II
Plus with the cover off.
This is an unsafe practice
and may cause injury.
Ꮨ
- User’s Manual 1
- PRINTED ON RECYCLED PAPER 2
- Number History Date 3
- Revision Revision 3
- TABLE OF CONTENTS 5
- Table of Contents 7
- SECTION 1 11
- Important User Information 13
- Manual Organization 14
- Section 1 – Introduction 15
- DPC II Plus Overview 16
- EZ Welder 16
- Overview 16
- DPC II Plus 17
- Key Features 17
- SECTION 2 19
- Health and Safety Tips 21
- Plastics Health Notice 22
- Electrical Safety Grounding 22
- Instructions 22
- RFI Considerations 23
- SECTION 3 25
- Shipping Contents 27
- DPC Placement 27
- Rack Mounting 28
- (DPC II Plus only) 29
- Connect the Cables 30
- Jumper Block 31
- Part No. 200–1293 31
- Multiple Probe System 32
- Automated Thruster System 33
- Dukane Press System 34
- Electrical Power Switch 35
- SECTION 4 37
- Front Panel Layout 39
- 1. AC Power Section 40
- 2. Generator Status Panel 40
- System Status Display 41
- System Power Output Display 42
- 3. Process Control Panel 43
- PROCESS CONTROL 45
- WELD MODE 45
- HOLD TIME 45
- AFTERBURST 45
- SECTION 5 47
- Rear Panel Layout 49
- System Input Connector 50
- Input Signal Description 51
- System Output Connector 52
- Output Signal Description 53
- ON LINE 54
- Remote Amplitude Control 56
- Power Signal Output Module 57
- Press Control Module 58
- Section 5 – Rear Connectors 59
- Multi–Probe Master Module 60
- Multi–Probe Slave Module 60
- Jumper Block Options 61
- System Control Inputs 62
- SECTION 6 65
- Process Setup Menu 67
- TRIGGER METHOD 69
- SECTION 7 73
- Process Control Menu 75
- WELD TIME 77
- 0.500 SEC 77
- AUTO STOP 78
- WELD METHOD 79
- WELD BY TIME 79
- WELD BY ENERGY 79
- GROUND DETECT 79
- WELD ENERGY 80
- 125 J 80
- SCRUB TIME 81
- 0.075 SEC 81
- AUTO Probe 82
- WELD METHOD 83
- AFTERBURST DELAY 84
- 0.150 SEC 84
- Initiate Mode 86
- Auto Stop 86
- Head Up On Auto Stop 86
- Trigger Type 86
- Single/Dual Pressure Mode 86
- #1 TIME ENERGY 87
- WELD METHOD P1 88
- WELD METHOD P2 89
- WELD ENERGY P2 89
- 75 J 89
- HOLD TIME 90
- 0.500 SEC 90
- AFTERBURST DURATION 90
- 0.250 SEC 90
- 0.750 SEC 91
- AMPLITUDE 92
- 75 % 92
- Parameter Min–Max Values 95
- SECTION 8 97
- Process Limits Menu 99
- LIMIT DEFINITION 100
- TOTAL TIME 101
- TOTAL ENERGY 101
- Dual Pressure Mode 102
- LIMIT DEFINITION 103
- SECTION 9 105
- Utilities Menu 107
- 1# 109
- OK TO COPY SETUP? 109
- NO 109
- YES 109
- COPY FROM 109
- Confirm Erase All Setups 110
- Erasing All Setups In Process 110
- Part Count Selection Menu 110
- Confirm Counter Enabled 110
- Confirm Reset Part Count 110
- Preset Part Count 111
- Cycle Press Off Line 111
- SECTION 10 113
- The Ultrasonic Probe 115
- Ultrasonic Horn 116
- Stack Assembly 117
- Attaching The Mounting 118
- Stud To A Horn Or A Booster 118
- Attaching The Horn To A 119
- Booster, Booster To A 119
- Probe, Or Horn To A Probe 119
- • 40kHz Stacks - 130 inch-lbs 120
- • 20kHz Stacks - 200 inch-lbs 120
- Stack Disassembly 121
- ISASSEMBLY 122
- Booster Notes 124
- Mounting The Stack 125
- SECTION 11 127
- Startup and Self–Test 129
- DPC System Test 130
- System Operation 131
- SECTION 12 133
- No Ultrasonic Output 135
- Generator 136
- Operate Input 136
- Generator FAULTs 137
- Generator Errors 138
- Section 12 – Troubleshooting 139
- Error Messages 141
- SECTION 13 143
- Front Panel 145
- Rear Panel 145
- Stack Surfaces 146
- Crowning 147
- Center Depression 147
- Corrosion 147
- Reconditioning 148
- Manual Resurfacing 149
- SECTION 14 151
- Contacting Dukane 153
- (630) 797–4987 154
- SECTION 15 155
- Regulatory Agency Compliance 157
- Dimensions 158
- Power Supply Requirements 159
- 2200-LN4-PE-L2 160
- SECTION 16 161
- Section 16 – Warranty 163
- APPENDIX A 165
- Appendix A – List of Figures 167
- APPENDIX B 169
- APPENDIX C 171
- Manual Switch Circuit 173
- Automation Switch Circuits 174
- Non–Isolated Switch Circuits 175
- Current Source Switch 176
- Isolated Switch Circuit 177
- Dukane ISO 189
- 40356601 190
Produits connexes et manuels pour Système de soudage Dukane DPC II Plus
(82 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels