Dukane DPC II Plus Manuel d'utilisateur Page 130
- Page / 190
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
120
Dukane Manual Part No. 403–566–01
DPC
™
II Plus and EZ Welder System – User’s Manual
DPC System Test
To test the DPC II Plus system’s ultrasound signal
delivery, perform the following steps.
1. For the initial test, the generator must be ON
LINE. Refer to step 5 on the previous page.
2. Position the probe so that its horn is not in con-
tact with anything. Do not hold the probe if you
are not accustomed to ultrasonic welding. The
initial ultrasonic sensation may surprise you and
cause you to drop the probe. Momentarily press
the generator control TEST key (G in Figure
11–2). The following conditions should occur.
3. One green segment of the System Power Out-
put bar display will light up indicating normal
operation (H in Figure 11–2.)
4. The ON LINE status indicator goes blank. This
indicates the ultrasonic probe is activated. The
probe should operate without any unusual
noise. The probe will operate as long as the
TEST key is pressed.
STATUS
FAULT
ON LINE
INPUT TEST
OVERTEMP
OVERLOAD
OFF LINE
ON
LINE
TEST
OFF
LINE
0
20 40
60
80 100
PERCENTAGE OF AVAILABLE POWER
PERCENTAGE OF AVAILABLE POWER
SYSTEM POWER OUTPUT
5. When the TEST key is released, the ON LINE
status indicator lights up again and the Power
Output display goes blank.
Figure 11–2 System Test Controls and Indicators
NOTE
Neither a press system, automation system,
hand probe or TEST key can trigger the gen-
erator to produce an ultrasound output if the
DPC II Plus is OFF LINE.
The Front Panel Control Lock (Pin No. 15 on
the HD–15 System Input connector) will dis-
able the TEST key from producing an output.
Refer to Section 5, Table 5—I.
The F P Control Lock will also inhibit any pro-
gramming changes. The menu navigation will
function normally, but data entry is inhibited.
- User’s Manual 1
- PRINTED ON RECYCLED PAPER 2
- Number History Date 3
- Revision Revision 3
- TABLE OF CONTENTS 5
- Table of Contents 7
- SECTION 1 11
- Important User Information 13
- Manual Organization 14
- Section 1 – Introduction 15
- DPC II Plus Overview 16
- EZ Welder 16
- Overview 16
- DPC II Plus 17
- Key Features 17
- SECTION 2 19
- Health and Safety Tips 21
- Plastics Health Notice 22
- Electrical Safety Grounding 22
- Instructions 22
- RFI Considerations 23
- SECTION 3 25
- Shipping Contents 27
- DPC Placement 27
- Rack Mounting 28
- (DPC II Plus only) 29
- Connect the Cables 30
- Jumper Block 31
- Part No. 200–1293 31
- Multiple Probe System 32
- Automated Thruster System 33
- Dukane Press System 34
- Electrical Power Switch 35
- SECTION 4 37
- Front Panel Layout 39
- 1. AC Power Section 40
- 2. Generator Status Panel 40
- System Status Display 41
- System Power Output Display 42
- 3. Process Control Panel 43
- PROCESS CONTROL 45
- WELD MODE 45
- HOLD TIME 45
- AFTERBURST 45
- SECTION 5 47
- Rear Panel Layout 49
- System Input Connector 50
- Input Signal Description 51
- System Output Connector 52
- Output Signal Description 53
- ON LINE 54
- Remote Amplitude Control 56
- Power Signal Output Module 57
- Press Control Module 58
- Section 5 – Rear Connectors 59
- Multi–Probe Master Module 60
- Multi–Probe Slave Module 60
- Jumper Block Options 61
- System Control Inputs 62
- SECTION 6 65
- Process Setup Menu 67
- TRIGGER METHOD 69
- SECTION 7 73
- Process Control Menu 75
- WELD TIME 77
- 0.500 SEC 77
- AUTO STOP 78
- WELD METHOD 79
- WELD BY TIME 79
- WELD BY ENERGY 79
- GROUND DETECT 79
- WELD ENERGY 80
- 125 J 80
- SCRUB TIME 81
- 0.075 SEC 81
- AUTO Probe 82
- WELD METHOD 83
- AFTERBURST DELAY 84
- 0.150 SEC 84
- Initiate Mode 86
- Auto Stop 86
- Head Up On Auto Stop 86
- Trigger Type 86
- Single/Dual Pressure Mode 86
- #1 TIME ENERGY 87
- WELD METHOD P1 88
- WELD METHOD P2 89
- WELD ENERGY P2 89
- 75 J 89
- HOLD TIME 90
- 0.500 SEC 90
- AFTERBURST DURATION 90
- 0.250 SEC 90
- 0.750 SEC 91
- AMPLITUDE 92
- 75 % 92
- Parameter Min–Max Values 95
- SECTION 8 97
- Process Limits Menu 99
- LIMIT DEFINITION 100
- TOTAL TIME 101
- TOTAL ENERGY 101
- Dual Pressure Mode 102
- LIMIT DEFINITION 103
- SECTION 9 105
- Utilities Menu 107
- 1# 109
- OK TO COPY SETUP? 109
- NO 109
- YES 109
- COPY FROM 109
- Confirm Erase All Setups 110
- Erasing All Setups In Process 110
- Part Count Selection Menu 110
- Confirm Counter Enabled 110
- Confirm Reset Part Count 110
- Preset Part Count 111
- Cycle Press Off Line 111
- SECTION 10 113
- The Ultrasonic Probe 115
- Ultrasonic Horn 116
- Stack Assembly 117
- Attaching The Mounting 118
- Stud To A Horn Or A Booster 118
- Attaching The Horn To A 119
- Booster, Booster To A 119
- Probe, Or Horn To A Probe 119
- • 40kHz Stacks - 130 inch-lbs 120
- • 20kHz Stacks - 200 inch-lbs 120
- Stack Disassembly 121
- ISASSEMBLY 122
- Booster Notes 124
- Mounting The Stack 125
- SECTION 11 127
- Startup and Self–Test 129
- DPC System Test 130
- System Operation 131
- SECTION 12 133
- No Ultrasonic Output 135
- Generator 136
- Operate Input 136
- Generator FAULTs 137
- Generator Errors 138
- Section 12 – Troubleshooting 139
- Error Messages 141
- SECTION 13 143
- Front Panel 145
- Rear Panel 145
- Stack Surfaces 146
- Crowning 147
- Center Depression 147
- Corrosion 147
- Reconditioning 148
- Manual Resurfacing 149
- SECTION 14 151
- Contacting Dukane 153
- (630) 797–4987 154
- SECTION 15 155
- Regulatory Agency Compliance 157
- Dimensions 158
- Power Supply Requirements 159
- 2200-LN4-PE-L2 160
- SECTION 16 161
- Section 16 – Warranty 163
- APPENDIX A 165
- Appendix A – List of Figures 167
- APPENDIX B 169
- APPENDIX C 171
- Manual Switch Circuit 173
- Automation Switch Circuits 174
- Non–Isolated Switch Circuits 175
- Current Source Switch 176
- Isolated Switch Circuit 177
- Dukane ISO 189
- 40356601 190
Produits connexes et manuels pour Système de soudage Dukane DPC II Plus
(82 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.373 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels